NEW: Special Financing - Click Here

DECO 2K – 5 gal. Kit SLR-DECO2K

$299.00 Add to cart

Shipping Cost: $19.99

Product Information

Order DECO 2K - 5 gal. Kit SLR-DECO2K DECO 2K - 5 gal. Kit SLR-DECO2K @ $299.00

Heal and Seal Deco 2K takes the durability and resiliency of the original Heal and Seal Deco and makes it into an uncompromising, apply-and-forget-it product.

It is simply put, the very best decorative concrete sealer on the market for its coverage, durability, and ease of use.

Features

  • Better coverage than acrylics
  • Increased durability
  • Superior chemical resistance
  • High heat resistance
  • Phenomenal UV resistance
  • Excellent against road salt and related chemicals

Deco 2K can be used to replace your current sealer and provide stellar results. Heal and Seal Deco contains NO acrylic resins and instead, works thru an advanced silicon technology that provides a permanent treatment protecting and preserving your concrete longer than any acrylic based sealer can possibly do. This concrete sealer will penetrate and chemically fuse just below and above the surface of the concrete.(Figure 1) This prevents to ability of water and other material to get below the surface and cause issues. This fused layer will also fill and heal small imperfections in the surface that would eventually lead to both aesthetic and physical imperfections in the surface. These imperfections can lead to color fade, concrete dusting, popouts, scaling, and even cracks.(Figure 2) Standard sealers do not offer the level of protection that Heal and Seal Deco 2K can provide. If applied properly it will never peel like a traditional sealer because it is more than just a plastic skin sitting on the surface. Once chemically bonded into the surface it will not peel and flake away. It is a permanent treatment that will only wear away as the actual concrete wears. This sealer protection will continue to keep your concrete healthy down below even when the top layer eventually shows wear.

Do yourself a favor and protect your investment with the only decorative concrete sealer that will maintain the health and welfare of your beautiful hardscape.

In addition to decorative concrete surfaces, Heal and Seal Deco 2K is also an excellent choice for restoring the color of weathered pavers. It is very easy to apply, provides instant gratification and with minimal cleanup.

Coverage approximately 275-300 sq feet per gallon with single coat coverage in many cases.

HOW TO USE:

MIXING: Always mix product before using to ensure to correct any possible separation that may have occurred. Material may separate during long term storage. Highly recommended to use a drill mixer with a mix head that lifts material toward the top surface to ensure a good blend. Blend for 2 minutes. Only combine enough part a and part b to give you the amount of sealer you will apply within 24 hours. Blend 4 parts a to one part b.Mix for three minutes at a low slow speed.

APPLICATION: Concrete should be clean and dry. Any previous sealer or coatings should be stripped and Removed to ensure heal and Seal is able to reach the concrete surface, It is always recommended to wait at least 28 days before applying to newly poured slabs. Excess moisture in the concrete can slow the curing process of the sealer and delay the time at which you are fully protected. Standard application should be to spray with a quality sprayer with a conical type tip and backroll. Apply with slight overlap on spray passes taking care not to create heavy puddles. Another person should begin rolling the material out into an even coating taking care to redistribute heavier areas of the sealer onto lighter areas. You should quickly find the sealer spreads out quickly and easily into a nice even coating. Failure to apply with this method can result in uneven darkening of the surface. When sealing countertops you need to be sure you are always rolling our material with a wet roller. Always be pushing material in front of roller and work into the surface. When the surface is fully coated you can then continue to roll out until material is gone. You may even “wring out” your roller of excess material if too much is on the surface once it is fully coated. Heal and Seal Deco 2K will create a white surface that will absorb and react with the concrete surface and cures clear as this happens. Failure to remove puddle areas can result in areas that will cure out much slower. Allow to dry for a minimum of one to two hours depending on current conditions of temperature, humidity and starting moisture in the concrete. For best results allow Heal and Seal to cure for up to 12 hours if possible. Once cured you can resume normal activity on the surface. In most cases, a second coating is not necessary unless there is a visual indication that some areas absorbed much more material than others. If so, the second coating should be applied only after the initial coating has cured – NO LONGER TACKY. Follow the same application procedure.

WARNING: Areas that remain white are indications of moisture present in that area or the material being applied to thick in that area. These areas could take a few extra days to cure fully but always do.

PLEASE NOTE: It is always recommended to test the product in a small, inconspicuous area (on the same concrete substrate) for desired results prior to application. Coverage rates may vary for all coatings and substrates depending on porosity, density, texture etc. When applying, do not exceed 400 sq. ft. per gallon. Applying too thin of a coating may cause inadequate film formation or performance expectations may be limited.